bleedblack
New member
Just looked at some pics of Doud Aldrich's rig. I didn't recognise anything in his rack, and wondered if anyone knows what he's got in there? What's he usin' for effects etc....
Juggernaut
Well-known member
wheres the pic?
bleedblack
New member
bleedblack
New member
crwnedblasphemy
Well-known member
a Roland Reverb/effects unit
A crybaby wah rack unit.....a mosvalve poweramp, and a Parametric eq.
That looks about it.
A crybaby wah rack unit.....a mosvalve poweramp, and a Parametric eq.
That looks about it.
bleedblack
New member
....so are those Cameron modded heads?
Juggernaut
Well-known member
The para-eq is a Furman pq-3
lordriffenstein
New member
From top to bottom:
Furman power unit
CAE rack interface
Rack Crybaby
Roland delay unit
CAE 4x4 looper
Furman PQ-3 equalizer
CAE Mini-mix
Boss SE-50/70
CAE interface
Mosvalve power amp
Furman power unit
CAE rack interface
Rack Crybaby
Roland delay unit
CAE 4x4 looper
Furman PQ-3 equalizer
CAE Mini-mix
Boss SE-50/70
CAE interface
Mosvalve power amp
evhfan
Member
those pics are from many years ago...it may have changed
bleedblack
New member
Thanks for the reply's everyone. Yea, I think the pics are quite old. His site dont seem to have been updated for a while. Does anyone know if he runs straight into the heads or does he hit the front end with any overdrive pedals etc? His sound is very saturated and tight, reminds me a bit of Sykes.
bleedblack
New member
......infact, does anyone recon you could get that kind of tone out of the new JVM? I'm in the u.k., and there's no way I could get my hands on a modded marshall 
MrDan666
Active member
:|::QBB:
Doug filled me in on this info a while back, when i asked him this same Question. He hits the front end of the marshalls with a furman PQ-3 or Boss DS-1 or both combined. He runs Wet/Dry/Wet. Amp head plugged into a dry cab, then the line out from that head feeds his FX which go to his poweramp and into left and right Wet 4x12s.
He absolutely nails that Sykes neck pickup tone on the Whitesnake songs!
bleedblack":3565c said:
Doug filled me in on this info a while back, when i asked him this same Question. He hits the front end of the marshalls with a furman PQ-3 or Boss DS-1 or both combined. He runs Wet/Dry/Wet. Amp head plugged into a dry cab, then the line out from that head feeds his FX which go to his poweramp and into left and right Wet 4x12s.
He absolutely nails that Sykes neck pickup tone on the Whitesnake songs!
Chubtone
Well-known member
Dougs been using that Furman PQ-3 for 20+ years with his Marshalls. It's amazing what one of those run in front of a stock Marshall or Boogie will do to the gain. If you run into the low input and raise the input level that thing is probably the best "OD pedal" or "boost" ever!
TOStudent
New member
:|::QBB:
When I picked up my head from him.
Mark said Doug was using Johns for Rythm and Marks for lead.
I think Doug also got the Standel for cleans from Mark because I think Mark worked for them.
Recently on Doug's site he mentioned that he switches heads depending on the venue for best sound.
SgtThump":7099f said:
When I picked up my head from him.
Mark said Doug was using Johns for Rythm and Marks for lead.
I think Doug also got the Standel for cleans from Mark because I think Mark worked for them.
Recently on Doug's site he mentioned that he switches heads depending on the venue for best sound.